| Lightened mounting plate | 3.33 | 3 | 2.00–4.00 | 2.00, 4.00, 4.00 |
| Two-part fastened enclosure | 1.00 | 3 | 1.00–1.00 | 1.00, 1.00, 1.00 |
| Sheet-metal L-bracket (flat pattern) | 3.33 | 3 | 3.00–4.00 | 3.00, 4.00, 3.00 |
| Laser-cut tab-slot panel | 2.67 | 3 | 2.00–4.00 | 2.00, 4.00, 2.00 |
| Two-body enclosure (no fasteners) | 1.00 | 3 | 1.00–1.00 | 1.00, 1.00, 1.00 |
| Fastened two-body enclosure (no BOM) | 1.00 | 3 | 1.00–1.00 | 1.00, 1.00, 1.00 |
| DFM-tight enclosure (no BOM) | 1.00 | 3 | 1.00–1.00 | 1.00, 1.00, 1.00 |
| Sheet-metal L-bracket (tight tolerances) | 2.67 | 3 | 1.00–4.00 | 1.00, 3.00, 4.00 |
| Laser-cut tab-slot panel (tight tolerances) | 2.33 | 3 | 2.00–3.00 | 3.00, 2.00, 2.00 |
| Laser-cut tab-slot panel (native vector) | 0.00 | 3 | 0.00–0.00 | 0.00, 0.00, 0.00 |
| Laser-cut bridge and web panel (native vector) | untested |
| Kerf-aware multi-part laser nest (native vector) | untested |
| Reverse-engineered bracket | 2.00 | 3 | 1.00–4.00 | 4.00, 1.00, 1.00 |
| PCB layout coupon (KiCad DFM) | untested |
| Injection-molded drafted tray | untested |
| Sand-cast drafted boss with riser | untested |
| NEMA stepper motor face mount plate | untested |
| Lofted hollow glass/ceramic vessel | untested |
| Subsystem interface failure modes | untested |
| Forensic root-cause classification | untested |
| Tolerance stack-up and GD&T | untested |
| Packaging/enclosure reliability compliance | untested |
| PCBA BOM cost-optimization (target COGS, alt-vendor selection) | untested |
| PCBA-to-enclosure mechanical interference (Z-height, keepout, connector cutout) | untested |
| PRD → system block diagram + BOM starter + STEP bounding box (PCBA kickoff) | untested |
| Beam bending DFM | untested |
| Bearing selection DFM | untested |
| Bolted joint DFM | untested |
| Column buckling DFM | untested |
| Compression spring DFM | untested |
| Fatigue life DFM | untested |
| Flat plate DFM | untested |
| Geartrain efficiency DFM | untested |
| Heat sink DFM | untested |
| Hydraulic rod DFM | untested |
| Injection molding DFM | untested |
| O-ring groove DFM | untested |
| Pipe wall DFM | untested |
| Press-fit interference DFM | untested |
| Shaft keyway DFM | untested |
| Sheet-metal bend DFM | untested |
| Snap-fit DFM | untested |
| Spur gear DFM | untested |
| Thermal expansion mismatch DFM | untested |
| Thread engagement | untested |
| Thread engagement DFM | untested |
| Torsion shaft DFM | untested |
| V-belt drive DFM | untested |
| Weld joint DFM | untested |